tag:blogger.com,1999:blog-1912157028983075300.post1941067708648092295..comments2023-07-13T07:01:22.307-07:00Comments on This Old Spoon: Updating Your Printrboard Firmware (OS X)Spoon (Jim Lind)http://www.blogger.com/profile/01802214706659967893noreply@blogger.comBlogger9125tag:blogger.com,1999:blog-1912157028983075300.post-66613712578378355782015-08-21T17:59:32.944-07:002015-08-21T17:59:32.944-07:00This comment has been removed by the author.Anonymoushttps://www.blogger.com/profile/14779901959165461844noreply@blogger.comtag:blogger.com,1999:blog-1912157028983075300.post-70567031833681947842015-07-06T11:21:54.180-07:002015-07-06T11:21:54.180-07:00@Robert, thanks for hunting it down. I'm sure ...@Robert, thanks for hunting it down. I'm sure it'll help somebody out.Spoon (Jim Lind)https://www.blogger.com/profile/01802214706659967893noreply@blogger.comtag:blogger.com,1999:blog-1912157028983075300.post-18916873066367058562015-06-19T15:51:41.213-07:002015-06-19T15:51:41.213-07:00Line 295 of Configuration.h is where you flip the ...Line 295 of Configuration.h is where you flip the y-axis, change the value from true to falseAnonymoushttps://www.blogger.com/profile/05563923189080998958noreply@blogger.comtag:blogger.com,1999:blog-1912157028983075300.post-47313972874771321132015-04-24T14:41:23.386-07:002015-04-24T14:41:23.386-07:00ThanksThanksAnonymoushttps://www.blogger.com/profile/05359957766938559203noreply@blogger.comtag:blogger.com,1999:blog-1912157028983075300.post-5605876934984118912015-04-24T12:51:00.529-07:002015-04-24T12:51:00.529-07:00Release notes on the Firmware state that the 1403 ...Release notes on the Firmware state that the 1403 is intended for the Simple Maker 1405 as well. My Printrboard is a Rev. D (same as yours) and I didn't have any issues with the 1403 Firmware.Spoon (Jim Lind)https://www.blogger.com/profile/01802214706659967893noreply@blogger.comtag:blogger.com,1999:blog-1912157028983075300.post-11119752908178736142015-04-24T07:13:24.490-07:002015-04-24T07:13:24.490-07:00that is 1405 .. that is 1405 .. Anonymoushttps://www.blogger.com/profile/05359957766938559203noreply@blogger.comtag:blogger.com,1999:blog-1912157028983075300.post-22130654694837000772015-04-24T06:39:33.640-07:002015-04-24T06:39:33.640-07:00Spoon
Great guide do you have a link to the prit...Spoon <br /><br />Great guide do you have a link to the pritrbot 1504 makers rev.d firmware so i can do this mod? Anonymoushttps://www.blogger.com/profile/05359957766938559203noreply@blogger.comtag:blogger.com,1999:blog-1912157028983075300.post-12675378451980683162015-04-23T08:50:38.734-07:002015-04-23T08:50:38.734-07:00The official Printrboard firmware flip-flopped on ...The official Printrboard firmware flip-flopped on stepper wiring as well between updates. I don't know how closely they were following the marlin source at the time. I agree that flipping a connector is easier than flashing the board again.Spoon (Jim Lind)https://www.blogger.com/profile/01802214706659967893noreply@blogger.comtag:blogger.com,1999:blog-1912157028983075300.post-26783457046427391962015-04-16T22:31:39.054-07:002015-04-16T22:31:39.054-07:00The Y stepper wiring is backward in the marlin sou...The Y stepper wiring is backward in the marlin source. I just flipped my connector around, but maybe I could edit the config.h if I knew where to look ... maxadamhttps://www.blogger.com/profile/08336722264022071775noreply@blogger.com